2 620-7921 Rev A STAR TRAC 14410 Myford Road Irvine, CA 926060 USA WORK INSTRUCTIONS, E-TBT / E-TBTe INSTALLATION
11 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe an
12 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. Embedded display console. 2. O
13 620-7921 Rev A Step 5. Disconnect the ground cable from the ground quick disconnect tab on the embedded display. Save the cable for l
14 620-7921 Rev A Step 9. Now screw in the coax adaptor to the coax ca-ble coming out of the base neck. Step 11. Take the embedded display
15 620-7921 Rev A Step 15. Next plug in the coax cable to the coax adapter on the tuner card of the embedded display as-sembly. Step 16.
16 620-7921 Rev A Step 20. Using a Phillips head screw driver, secure the front display to the back with (8) M4 x 0.7 x 19mm lon
17 620-7921 Rev A Step 21. Now it is time to connect entertainment cable and power to the unit. Connect the in-house entertainme
18 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe an
19 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. iPod® center console. 2. iPod®
20 620-7921 Rev A Step 5. Disconnect the ground wire between the heart rate board and the display mount. Step 6. Disconnect the 12-pin serial c
3 620-7921 Rev A GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations ma
21 620-7921 Rev A Step 9. Using a #2 Phillips head screwdriver, remove the (4) screws that hold bottom side of the dis-play console on,
22 620-7921 Rev A Step 13. Now install the new head phone jack mount. Use the screw saved from the earlier step to se-cure the mount to the dis
23 620-7921 Rev A Step 17. Take the headphone jack cable from the center console and connect it to the newly installed headphone jack in
24 620-7921 Rev A Step 23. Install the CSAFE power connector on the new bottom plastic cover. Step 24. Install the new bottom plastic cover on
25 620-7921 Rev A Step 26. Take the front display plastics with the new cen-ter console to the base unit. Hold the front dis-play plastics at t
26 620-7921 Rev A Step 30. Plug back the Heart rate ground cable into the quick disconnect tab on the display mount. Step 31. Plug the
27 620-7921 Rev A Step 33. Using a Phillips head screw driver, secure the front display to the back with (8) M4 x 0.7 x 19mm lo
28 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe an
29 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: 1. MYE® center console. 2.
30 620-7921 Rev A Step 5. Disconnect the 12-pin serial connector from the display Step 6. Now disconnect the heart rate connector from th
4 620-7921 Rev A Step 1. Lay the box with heavy end facing down in the area where it is going to be assembled. Cut and remove packaging stra
31 620-7921 Rev A Step 9. Next remove the bottom cover, then remove the headphone blank cover. You will no longer need those covers and th
32 620-7921 Rev A Step 13. Identify the cables coming out of the new center console: 1. Center console keypad ribbon cable. 2. Center console
33 620-7921 Rev A Step 17. Take the new iPod® cradle from the kit and in-stall it onto display console. Step 18. Now connect iPod® cable from
34 620-7921 Rev A Step 23. Take the front display plastics with the new cen-ter console to the base unit. Hold the front dis-play plastics at th
35 620-7921 Rev A Step 25. Plug-in the 12-pin main I/O cable from the neck to the new 12 pin adaptor. Step 27. Plug back the Heart rate gro
36 620-7921 Rev A Step 29. Assemble the front and back display parts to-gether by sliding the bottom of the front display under the 2 tabs
37 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe an
38 620-7921 Rev A Step 1. Remove all contents from the packaging and verify that you have the following parts: Step 3. Using a #2 Phillips scr
39 620-7921 Rev A Step 5. Disconnect the ground wire between the heart rate board and the display mount. Step 6. Disconnect the 12-pin serial c
40 620-7921 Rev A Step 9. Remove the cap cover with the Star Trac logo from the back cover plastics by removing the (2) screws using a
5 620-7921 Rev A Step 5. Remove remaining packaging ma-terials and lay all components on the floor. Step 6. Verify the following components are
41 620-7921 Rev A Step 13. Using a #2 Phillips head screwdriver, remove the (4) screws that hold the bottom cover of the display console,
42 620-7921 Rev A Step 17. Install the iPod® cable into the iPod® cradle on the front side of the display console by removing the plug from the
43 620-7921 Rev A Step 22. Connect the seven-pin interface cable from the console to J14 connector on the display board. Step 23. Now conn
44 620-7921 Rev A Step 26. Identify the four cables coming out of the neck and mounting bracket: 1. Heart rate cable 2. Main I/O cable
45 620-7921 Rev A Step 29. Take the 5” piece of tape from the PVS kit and wrap the connectors so that all of the metal sur-face is covered. Step
46 620-7921 Rev A Step 33. Plug the DC power cable from the base neck to either one of the DC connectors on new center console board. Then pl
47 620-7921 Rev A Step 37. Plug back the Heart rate ground cable into the quick disconnect tab on the display mount. Step 38. Plug the
48 620-7921 Rev A Step 42. Now it is time to connect entertainment cable and power to the unit. Connect the in-house entertainme
49 620-7921 Rev A ATTENTION • Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe an
50 620-7921 Rev A STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714) 669-1660 Fax: (714) 508-3303 http:
6 620-7921 Rev A Step 1. Route display cables up through upper half of neck through the holes provided. Step 2. Insert the upper half
Star Trac FitnessTME-TBT Total Body TrainerO WNER’ S M ANUAL
STAR TRAC E SERIES TOTAL BODY TRAINERS OWNER’S MANUAL 25After using your STAR TRAC E SERIES TOTAL BODY TRAINERS for a period of time, you may wish to
The following keys are available in MAINTENANCE MODE:Upper and Lower Data Information Window SCROLL Keys: Display the next and previous parameters, re
STAR TRAC E SERIES TOTAL BODY TRAINERS OWNER’S MANUAL 27Lowest Highest DefaultItem Value Value Value MeaningCW Prog 0 65535 0 Number of times the Cont
7 620-7921 Rev A Step 5. Using provided screwdriver, remove the M4 x 0.7 screws that hold the display assembly to-gether, then se
8 620-7921 Rev A Step 9. Identify the four cables coming out of the neck and mounting bracket: 1. Heart rate cable 2. Main I/O cable 3
9 620-7921 Rev A Step 13. Assemble the front and back display parts to-gether by sliding the bottom of the front display under the 2 tabs
10 620-7921 Rev A Step 17. Place the Total Body Trainer on the floor in the position it will be used. Then adjust leveling feet to assu
Comentários a estes Manuais